Making An Insulated Loft Trapdoor

insulated loft trapdoor in place

Introduction

I recently had a ground floor extension built which required access to the loft space in the pitched roof to provide and service pipes and cables. So I asked the builder to create an insulated loft trapdoor. I made it clear that it should not just be a sheet of MDF or plywood. It must have thermal insulation fixed to it to prevent it forming a cold spot in the ceiling. I also required it to be out of sight if possible. By that I meant he must avoid putting it in the main reception room of the extension.

By widening the gap between two ceiling joists he made an opening 485mm wide. Enough to accommodate a telescopic ladder I bought to climb into the loft.

The builder built the opening and finished it with architrave around it and clapping strips on all sides to form a lip that supports the insulated loft trapdoor. I offered to make the insulated loft trapdoor myself since it wasn’t part of the original estimate. That allowed the builder to get on with work that was part of the original estimate.

Making The Insulated Loft Trapdoor

NOTE: This is not a trapdoor capable of taking the weight of anyone standing on it. It is not intended to be closed while anyone is in the loft.

Below is the loft opening I had to close with an insulated loft trapdoor:

Loft with trapdoor open
The loft opening with internal measurements above the lip = 790mm x 510mm.

Making it strong but light-weight I used 9mm MDF for the trapdoor base, which sits in the opening 790mm x 510mm, and 5mm ply to build a box for holding the insulation.

NOTE: An area of 5mm ply is lighter than the same area of 9mm (or thicker) MDF.

Below is the type of insulation I used. It was left over by the builder when he insulated the floor:

RECTiCEL insulation
75mm RECTiCELTM insulation

I had sufficient 75mm RECTiCELTM insulation left by the builder to cover the trapdoor with a double layer 150mm thick.

I formed the trapdoor into a box, with sides made of 150mm x 5mm plywood, and cut two pieces of insulation to be a tight fit within the box.

On similar projects in the past I may have fixed the plywood with screws and adhesive to a framework of 25mm x 25mm timber. In this case I chose to use hot-melt glue to bond each side to the base and to its adjacent sides.

Box Construction

Materials and Tools Required:

  • a hot-melt glue gun,
  • hot-melt glue sticks,
  • 9mm MDF,
  • 5mm plywood,
  • a pencil,
  • a steel metric tape measure,
  • a straight edge,
  • an engineer’s square.

Method and Instructions

I followed these instructions to form the trapdoor into a box for holding thermal insulation:

  1. Measure the hole above the clapping strips for length and width and cut the MDF to fit, leaving a 1mm gap all around.
  2. Draw a rectangle on the upper surface of the MDF with all sides 15mm from the nearest edge.
  3. Cut 2 pieces of 150mm x 5mm ply the width of the rectangle to make sides 1 & 3.
  4. Cut 2 pieces of 150mm x 5mm ply, the length of the rectangle + 10mm, to make sides 2 & 4.
  5. Take side 1 and stand it along the outside of the rectangle on a narrow side and tack it in place with hot-melt glue.
  6. Use an engineer’s square to set it vertical while the glue hardens.

    insulated loft trapdoor side 1
    The first side is tacked into position with hot-melt glue.
  7. Take side 2 and stand it along the outside of the rectangle on a long side and tack it in place with hot-melt glue.
  8. Check that side 2 overlaps side 1 and glue the two pieces together at the top corner. The presence of the first side will ensure that the second side is set vertical.

    insulated loft trapdoor showing sides 1 & 2
    The second side is tacked into position with hot-melt glue.
  9. Take side 3 and stand it along the outside of the rectangle on the other short side and tack it in place with hot-melt glue.
  10. Check that side 2 overlaps side 3 and glue the two pieces together at the top corner. Careful alignment of sides 2 and 3 will ensure that side 3 is also vertical.
  11. Stand side 4 along the outside of the rectangle’s other long side and tack it in place with hot-melt glue.
  12. Check that side 4 overlaps side 1 and side 3 and glue the three pieces together at the top corners. The presence of sides 1 and 3 will ensure that the fourth side is set vertical. See the corner detail in this drawing. It shows how the sides butt up against each other.

    insulated loft trapdoor showing all sides
    The fourth side is tacked into position with hot-melt glue.
  13. Finally run hot-melt glue along the inside of all the corners and along the outside edges of all the plywood side where they come into contact with the upper surface of the trapdoor.
  14. Allowed fifteen minutes for all the glue to cool down.

Cutting The Insulation

If a crosscut saw, intended for cutting across wood grain, is used to cut this type of insulation an unnecessary amount of sawdust is generated. So I use a knife with a smooth blade. I found the OXO Good Grips Natural Grip bread knife is very good for this because it has a handle shaped so it is held like a wood saw. This bread saw doesn’t have teeth, just a wobbly edged knife blade. Unfortunately it seems to have gone off the market. Below is a picture of it anyway:

OXO Good Grips Natural Grip Bread Knife
OXO Good Grips Natural Grip Bread Knife

Note: Similar OXO bread knives are available but with a straight handle like most knives have.

The Completed Insulated Loft Trapdoor

Below is the completed insulated loft trapdoor with two identically cut pieces of insulation  pressed into the trapdoor box one on top of the other:

Completed Insulated Loft Trapdoor
Completed Insulated Loft Trapdoor

The glue that was applied with a hot glue gun can clearly be seen around the edge bonding the sides firmly to the base.

Below: The insulated loft trapdoor is seen turned upside down and painted with a gloss topcoat.

Painted Insulated Loft Trapdoor
Painted Insulated Loft Trapdoor

Lifting The Trapdoor Into Place

The trapdoor is put in place by climbing on short steps placed below the opening. Then the narrow edge is fed through at an angle to avoid the roof above. Eventually it’s laid horizontally above the opening so it rests on the loft insulation at the side. It is then drawn across the opening by balancing it on the outstretched fingers of both hands. Then it’s turned to true it up with the opening and lowered into position.

I had to trim one corner of the trapdoor with sandpaper to get it to fit. Then I marked an ‘A’ on the plywood and the loft timbers to show which way round it must be presented.

Author: Helpful Colin

I have a background in telecommunications and a fascination with all things scientific and technical - from physics to electronics, and computing to DIY.

Please Comment Below (or Select An Existing Comment's "REPLY" Button First) - See HELP for Details.