A few months ago my eleven year old Panasonic 1000 Watt Slimline Combi Microwave Inverter (Model: NN-A574SBBTQ) developed a problem which was only visual. The large rectangular button used to open the door began protruding on the right end by about five millimetres. Operation of the machine wasn’t impaired but continuous use with the faulty button led to further problems when the button jammed and I couldn’t easily open the door. In the end I had to make microwave inverter repairs to the door opening button and to the door bezel when it later came adrift.
Unfortunately besides my Dualit Milk Frother requiring a repair (see How I Repaired A Dualit Milk Frother Model DMF2) another problem has developed. I have to ask, “Is my Dualit Milk Frother corroding?” If not what is happening to it. Is the brown mark I can see copper or rust?
My wife pressed the start button on the Dualit Milk Frother (Model DMF2) one day in the summer of 2017 and it no longer worked. This persisted so we had to heat the milk in the microwave oven for a week or two until we got a new frother.
Of course, me being me, I dismantled the faulty Dualit Milk Frother to see if there was an obvious problem. There wasn’t anything burnt out or blackened. Just a lot of wiring in a very confined space. It was constructed with a flat straight circuit board fitted into a curved space. No-one had used flexible circuit boards here.
The long term solution was to replace the whole Dualit Milk Frother. Since they are still on the market that’s what I chose to do. The faulty one had been a replacement for our Nespresso Aeroccino Milk Frother already mentioned in this blog. We now had to replace the replacement.
It must be nearly two years ago that I first had a problem with my Dishwasher Rinse Aid Dispenser Catch. The tab that has to be pushed towards the top of the door to open the rinse aid dispenser, so that more rinse aid can be added, had somehow broken and disappeared. I found I could continue to open it by pressing the remaining catch towards the top of the door using the handle end of a teaspoon.
Since refilling the rinse aid dispenser doesn’t happen everyday I was happy to continue with that opening method indefinitely. However about six months ago I found the entire catch was missing leaving the rinse aid dispenser door flapping in the breeze. I searched inside the dishwasher and found the plastic part of the catch but not the coil spring. Also when I inserted the catch its retaining clips no longer wanted to spring outwards and perform their retaining action. The whole plastic catch appeared to have been eroded by the dishwashing process. I noticed that the dishwasher liquid dispenser catch looks similarly eroded, but that works on a different principal and is still O.K. The detergent and rinse aid compartment covers are made of a different plastic which has not shown signs of erosion.
After several months without using rinse aid I decided I should take action to fix the catch.
I’ve had a Nespresso Pixie since June 2012 and at the same time I acquired a Nespresso Aeroccino milk frother (Aeroccino 3 to be precise). These devices are very nice to have and work well even after 2½ years continual use. The coffee is very nice too.
However there is a slight problem with the Nespresso Aeroccino milk frother but it is not insurmountable. It’s very easy to burn milk on the bottom where the most intense heat is applied. You can see it burnt on in this picture where the whisk has been removed.
This article advises how to keep a Nespresso Aeroccino milk frother clean. There are pictures portraying the burnt milk problem and advice is given on how to avoid it.
This article advises how to perform Dyson Slim DC18 Cleaner Head Maintenance. This can involve removing the Brushbars to remove items that have got wrapped around them and removing the Soleplate for access so dirt can be cleaned out. In extreme cases the Motor Housing can be opened so that dirt can be sucked out of it too.
Many devices in this world which pump air have air filters. They’re installed to stop dirt harming mechanisms, bearings, etc.. Without filters that dirt would ultimately make them perform badly or fail. The air filters clog up instead and have to be replaced or cleaned at regular intervals. The Dyson Slim DC18 is no different. It has two air filters, one to protect the motor and the other (the HEPA filter) to protect the local environment and the people in it.
Some people think teapot cleaning is unnecessary and that it spoils the flavour of the tea. If they have traditional brown earthenware teapots they probably don’t see all the tannin stains on the inside. With a stainless steel teapot you see them all and they start to form very quickly from new, or after cleaning. Tannin makes a teapot look disgusting. Not something you want guests to see when you make them a cuppa, or when they make one for you.
Teapot cleaning can be avoided by keeping it clean. One way is to make sure it’s emptied and rinsed out immediately after use. Letting it stand with old tea in it until the next mash allows the tannin deposits to grow.
This post gives a detailed description, with photos and reference to a Parts Diagram, of how to replace a Dyson Slim DC18 Undercarriage. The Undercarriage would require changing if part of it broke since parts cannot be obtained individually. I changed mine when the Air Input Changeover Valve Actuator broke.
“Since I first published this article, in February 2013, I have had plenty of feedback from readers and I have gleaned information from statistical data which has encouraged me to improve it. So if you came here soon after I published it you should find better information now. You will also find some photos of repairs carried out by readers of this post in Step 10.” — Helpful Colin
You may be surprised to learn that the shower head that came with my Mira Sport Thermostatic Shower is made from 22 separate parts. If you count them in the featured image above you will see 21 but take note that the main body of the shower head, on the right, is made from two inseparable parts of plastic.
I can also tell you that the main body of the shower head retains water after use. Some drops can be removed by shaking it in various ways but some always remains inside. If the shower isn’t used regularly this water will become stagnant and may hold dangerous bacteria. I would recommend turning the shower on at least once per week to refresh the water in the shower head.
This all came to light when I wanted to do a good job of cleaning mould and calcium off the shower head. I felt the best job would be done by dismantling it and cleaning all the parts individually since some mould looked as if it had penetrated inside.